Bathroom Project Part Two: Painting Walls & Tiles

Topics: DIY, Bathroom

bathroom project
The dreaded ‘before’ pic

 

As discussed in Bathroom Project Part One, there is always one room in a second hand house which tells you the previous owners were possibly colour blind and usually it’s the bathroom. Our previously loved home is no different. The bathroom we inherited was decorated in ghastly pink paint work matched with snot green tiles – one word ‘horrific’. Aside from the décor, the room had other issues: there was no storage, the shower was one of these hoses attached to the taps that you have to run around under to get wet, there was very little light, there was a leak at the bath taps and the wind tunnel caused by the draft from the ill-fitting vent was perishing mid-winter.

Having resolved the shower, leak and wind tunnel in Part One, the next step was to change the colours.

The colour choices of the previous owners, pink and green, while fine in theory, in reality were a daily assault on the senses. The tones selected did not work together, and both colours clashed with the grey floor tiles. Having successfully avoided the need to replace the wall tiles in Part One, I decided I would paint the existing ones rather than replacing them. I also decided that replacing the floor tiles was an unnecessary expense, and decided to use these as the base of my design.

The floor tiles were a slate grey colour, which made me decide that I would like the bathroom to have a masculine, utilitarian feel to it. As the bathroom is small I wanted to give the impression that the wall opposite the door appeared to be further away than it was. In order to do this I needed to choose a dark colour close to the door, which in theory in your mind’s eye pulls these walls closer to you as you walk in the door and a pale colour for the far wall, as pale colours give the impression of perceptual space, and thus the wall appears (again in theory) to be further away from you.

Bathroom Paint test

For the dark hues I choose to test a teal colour I had recently fallen in love with and a daring dark grey. As I do for wall colour choices, I purchased a tested and painted a big blob on a space on the wall at eye level that I frequently walk by or see, and left it for a week, to make sure I was not going to change my mind after painting the whole wall. As the family got used to the colour choices and they were debated over dinner, I cracked on with painting the tiles.

 

Bathroom Paint Tiles v2

I decided to keep the tiles simple, and chose to do them in white; partially because white is my favourite colour, partially because I think it lends itself to the masculine, utilitarian feel I was aiming for and partially because I already owned white tile paint from painting the kitchen tiles downstairs.

I started by removing all the hooks, shower heads, cabinets, whatever was attached to the tiles that could be removed – going around things carefully is so much more work that simply removing and replacing afterwards.

Next I cleaned the tiles thoroughly, and I mean thoroughly. I washed them with jif and dried, then bleached them with an old toothbrush and then cleaned them with sugar soap. There can be no residue of any sort on these tiles when you start painting, if there is, it will show in relief in the paint and cause chipping of the paint further down the line. Time invested in this deep clean will be returned tenfold in the quality of the end result.

Next I painted the tiles with a white primer, carefully avoiding both dribbles (by not overloading the brush) and cohesion patches (by making sure the tiles had no residue). Make sure you work the primer into the grout and every corner.

Before leaving the primer to dry give it a look over to ensure there are no imperfections and no dribbles. These are quick to fix while the primer is wet, but if you miss some and the primer is dry, just sand them down with fine sand paper and touch up as appropriate.

Although most primers only require one coat I did a second because I was covering dark tiles and I wanted a very crisp look.

Once the primer is dry add a layer of tile paint. Tile paint is an oil based paint like gloss paint and behaves the same way, so paint one side from the top to the bottom before moving on, because the paint will get tacky as it starts to dry.

Again I did a second layer of tile paint to ensure there were no shadows creeping through from the dark tiles underneath. Also because I went from left to right with the first layer, I went from right to left with the second. This means that the last place you did with the previous layer when you were tired, is now the first place you do refreshed and refocused for the next layer.

Once dry replace fittings.

 

The family decided that the grey actually worked the best, so while I had the paint brushes out, I painted all the walls grey.

 

Bathroom Grey
Nearly dry grey walls

 

 

Next stage is to get the furnishings and final touches – See this in Part Three

 

 

Advertisements

5 thoughts on “Bathroom Project Part Two: Painting Walls & Tiles

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s